Welcome : Guest
  • Home
  • Employees safety Practices

Employees safety Practices

It’s vitally important to take safety precautions when working with electricity. Safety must not be compromised and some ground rules need to be followed first. The basic guidelines regarding safe handling of electricity documented below will help you while working with electricity.

  1. Avoid water at all times when working with electricity. Never touch or try repairing any electrical equipment or circuits with wet hands. It increases the conductivity of electric current.
  1. Never use equipment with frayed cords, damaged insulation or broken plugs.
  1. If you are working on any receptacle at your home then always turn off the mains. It is also a good idea to put up a sign on the service panel so that nobody turns the main switch ON by accident.
  1. Always use insulated tools while working.
  2. Electrical hazards include exposed energized parts and unguarded electrical equipment which may become energized unexpectedly. Such equipment always carries warning signs like “Shock Risk”. Always be observant of such signs and follow the safety rules established by the electrical code followed by the country you’re in.
  1. Always use appropriate insulated rubber gloves and goggles while working on any branch circuit or any other electrical circuit.
  1. Never try repairing energized equipment. Always check that it is de-energized first by using an electric tester. Never use an aluminium or steel ladder if you are working on any receptacle at height in your home. An electrical surge will ground you and the whole electric current will pass through your body. Use a bamboo, wooden or a fibreglass ladder instead.
  1. Always check all your GFCI’s once a month. A GFCI (Ground Fault Circuit Interrupter) is a RCD (Residual Current Device). They have become very common in modern homes, especially damp areas like the bathroom and kitchen, as they help avoid electrical shock hazards. It is designed to disconnect quickly enough to avoid any injury caused by over current or short circuit faults.
  1. Always use a circuit breaker or fuse with the appropriate current rating. Circuit breakers and fuses are protection devices that automatically disconnect the live wire when a condition of short circuit or over current occurs. The selection of the appropriate fuse or circuit breaker is essential. Normally for protection against short circuits a fuse rated of 150% of the normal circuit current is selected. In the case of a circuit with 10 amperes of current, a 15 ampere fuse will protect against direct short circuits whereas a 9.5 amperes fuse will blow out.
  1. Working outside with underground cabling can be dangerous. The damp soil around the cable is a good conductor of electricity and ground faults are quite common in the case of underground cabling. Using a spade to dig at the cable can damage the wiring easily so it is better to dig at the cable by hand while wearing insulated gloves.
  1. Always put a cap on the hot/live wire while working on an electric board or service panel as you could end up short circuiting the bare ends of the live wire with the neutral. The cap insulates the copper ends of the cable thus preventing any kind of shock even if touched mistakenly.
  1. Take care while removing a capacitor from a circuit. A capacitor stores energy and if it’s not properly discharged when removed it can easily cause an electric shock. An easy way to discharge low voltage capacitor is that after removal from the circuit is to put the tip of two insulated screw drivers on the capacitor terminals. This will discharge it. For high voltage ones a 12 Volts light bulb can be used. Connecting the bulb with the capacitor will light up the bulb using up the last of the stored energy.
  1. Always take care while soldering your circuit boards. Wear goggles and keep yourself away from the fumes. Keep the solder iron in its stand when not in use; it can get extremely hot and can easily cause burns.
My Account
My Vault
My Payments
  • Know Your Bill

    Know Your Bill

    Know Your Bill

    Know Your Bill

    Know Your Bill

  • Customer Service

    Customer Service

    Customer Service

    Customer Service

    Customer Service

  • Manage Your Connection

    Manage Your Connection

    Manage Your Connection

    Manage Your Connection

    Manage Your Connection

Save Energy

Readmore..

Safety

Readmore..

Energy Conservation

Readmore..

Our Community

Readmore..

© 2017 ourcesu.com. All rights reserved. Do not reuse text or graphics without written permission. | Privacy Statement. Developed by : TNine Infotech